syntax = "proto3";

package request;
option go_package = "joylink.club/bj-rtsts-server/dto/request_proto";

// 继电器
message Relay {
  // 继电器操作
  enum Operation {
    Undefined = 0; // 未定义
    ForceQw = 1;   // 强制前接点位(吸起)
    ForceHw = 2;   // 强制后接点位(落下)
    CancelForce = 3; // 取消强制
  }
}

// 继电器操作请求
message RelayOperationReq {
  string simulationId = 1;         // 仿真id
  int32 mapId = 2;                 // 图id
  uint32 deviceId = 3;             // 设备id
  Relay.Operation operation = 4;   // 继电器操作
}

// 道岔
message Turnout {
  // 道岔操作
  enum Operation {
    Undefined = 0; // 未定义
    DC = 1;        // 定操
    CancelDC = 2;  // 取消定操
    FC = 3;        // 反操
    CancelFC = 4;  // 取消反操
    SetSB = 5;     // 设置失表故障
    CancelSB = 6;  // 取消失表故障
    SetJC = 7;     // 设置挤岔故障
    CancelJC = 8;  // 取消挤岔故障
    ForceDw = 9; // 强制定位
    ForceFw = 10; // 强制反位
    CancelForce = 11; // 取消强制
  }
}

// 道岔操作请求
message TurnoutOperationReq {
  string simulationId = 1;         // 仿真id
  int32 mapId = 2;                 // 图id
  uint32 deviceId = 3;             // 设备id
  Turnout.Operation operation = 4; // 道岔操作
}

// 信号机
message Signal {
  //信号机操作
  enum Operation {
    Undefined = 0;       // 未定义
    Display = 1;         //显示操作,如设置绿色、设置红黄色
    LightHFaultDs = 2;   //设置红灯断丝故障
    LightUFaultDs = 3;   //设置黄灯断丝故障
    LightLFaultDs = 4;   //设置绿灯断丝故障
    LightAFaultDs = 5;   //设置蓝灯断丝故障
    LightBFaultDs = 6;   //设置白灯断丝故障
    LightHCancelDs = 7;  //取消红灯断丝故障
    LightUCancelDs = 8;  //取消黄灯断丝故障
    LightLCancelDs = 9;  //取消绿灯断丝故障
    LightACancelDs = 10; //取消蓝灯断丝故障
    LightBCancelDs = 11; //取消白灯断丝故障
  }
}

// 区段
message Section {
  //区段操作
  enum Operation {
    SetDrst = 0;//设置计轴直接复位
    CancelDrst = 1;//取消计轴直接复位
    SetPdrst = 2;//设置计轴预复位
    CancelPdrst = 3;//取消计轴预复位
    SetFaultOcc = 4;    //设置故障占用
    CancelFaultOcc = 5; //取消故障占用
  }
}

//屏蔽门
message Psd {
  enum Operation {
    Undefined = 0;
    //屏蔽门控制
//    Km4 = 1; //四编组开门
//    CancelKm4 = 2; //取消四编组开门
//    Km8 = 3; //八编组开门
//    CancelKm8 = 4; //取消八编组开门
//    Gm = 5; //关门
//    CancelGm = 6; //取消关门
//    ForceKm4 = 7; //强制四编组开门
//    ForceKm8 = 8; //强制八编组开门
//    ForceGm = 9; //强制关门
    Km = 1; //开门
    CancelKm = 2; //取消开门
    Gm = 3; //关门
    CancelGm = 4; //取消关门
    ForceKm = 5; //强制开门
    ForceGm = 6; //强制关门
    CancelForce = 10; //取消强制
    //屏蔽门故障
    AsdCannotOpen = 11; //滑动门无法开门
    CancelAsdCannotOpen = 12; //取消滑动门无法开门
    AsdCannotClose = 13; //滑动门无法关闭
    CancelAsdCannotClose = 14; //取消滑动门无法关闭
    //间隙探测
    QDTC = 15; //启动探测
    CancelQDTC = 16; //取消启动探测
    TZTC = 17; //停止探测
    CancelTZTC = 18; //取消停止探测
  }
}

// 屏蔽门操作请求
message PsdOperationReq {
  string simulationId = 1;         // 仿真id
  int32 mapId = 2;                 // 图id
  uint32 deviceId = 3;             // 设备id
  Psd.Operation operation = 4; // 操作
  repeated int32 asdCodes = 5; //无法关闭/无法开启故障涉及的滑动门的编号
  int32 group = 6; //开门操作的编组
}